How To Register New Grandstream Phone In Sip

Grandstream: Setup and Configuration of the Grandstream GXP IP Phone with Telnyx

Learn how to set upwardly and configure a Grandstream GXP1630/GXP2135 IP Phone and connect it to your Telnyx account.

East

Written past Eliza Silvery
Updated over a week ago

Instructions for configuring the Grandstream GXP IP Telephone to work with Telnyx

In this activity you volition:

Go your device's IP address and log into the Gigaset telephone's spider web portal
Configure your GXP

Pre-requisites

Ensure that your Telnyx Mission Command Portal is configured properly
RECOMMENDED: Enable TLS to encrypt your traffic

Video Walkthrough

Setting up your Telnyx SIP portal account and then y'all can make and receive calls:

ane. Get your device's IP accost and log into your phone'southward web portal

In this step, you'll obtain the IP accost from your GXP, which you'll need to log into the spider web portal in the side by side step.

From your telephone, navigate to Menu >> Status >> Network Status >> IPv4 Address and take note of the IP address on this screen. You'll need it next.
On a computer connected to the same network as your phone, open a web browser and blazon http:// followed past the telephone's IP address into the accost bar of your browser.
Log into the portal. Out of the box, the default credentials are:
1. Username: admin
2. Password: admin

ii. Configure your Grandstream GXP

In this stride, you lot'll create a SIP trunk and connect your phone to Telnyx.

Click on Accounts in the superlative menu.
Aggrandize the business relationship you lot're looking to configure and click Full general Settings.

You can too use the top navigation to become here if y'all want.
On this folio, enter the following information:
1. Account Name: Give it a name that makes sense for you lot
  
  SIP Server: sip.telnyx.com
  
  SIP User ID: Your Telnyx SIP business relationship username
  
  Authenticate Password: Your Telnyx SIP account countersign
  
  Proper name: This is your caller ID. You can cull whatever yous like, but keep in mind the post-obit naming conventions:
  1. Caller ID Name should be in capital letter messages. This will appears more clearly/visible on some devices.
  2. You must NOT employ any special characters, every bit they will not be displayed. Spaces are immune.
  3. Some of regular Canadian providers will not show more than 15 characters. We propose shrinking or adjust your caller ID.
2. Voice Mail Access Number: *97
Now, while still in Accounts > Account 1 (or the business relationship you want to configure) click on SIP Settings > Basic Settings and provide the following information:
1. SIP Registration: Yes
2. Register Expiration: 5 (this is in minutes)
3. Enable OPTIONS Keep Live: Yes
4. Local SIP Port: 5060 if you accept non enabled TLS encryption. If you have, cull 5061.
5. SIP Transport: UDP or TCP if y'all have not enabled TLS encryption. If you accept, choose TLS/TCP.
*This screenshot demonstrates a connection that uses UDP transport.
Click Save and Apply.

That'due south information technology! You've finished configuring your Grandstream GXP contour, and can now start testing calls!

Troubleshooting

"I can receive incoming calls, only outgoing call are failing. The fault says 'No response'"

Answer

Log into the web portal and navigate to Accounts > Account 10 > SIP > Custom SIP Header and disable:
1. Use X-Grandstream-PBX Header
2. Use P-Admission-Network-Info Header
3. Apply P-Emergency-Info Header
Go to Accounts > Account X > SIP > Audio Settings, and choose codec G729A/B as preferred Vocoder.

Boosted Resources

Review our getting started with guide to make certain your Telnyx Mission Control Portal account is setup correctly!

Additionally, cheque out:

GXP1630 user guide
GXP1630 Admin manual
GXP2135 product documentation
GXP2135 user manual
GXP2135 admin manual

Can't find what you're looking for? Click the chat bubble at your lower correct hand corner and starting time a chat!